11 Strategies To Completely Block Your Car Key Button Repair

Car Key Button Repair
A damaged car key button can be a hassle. You might need to contact the 24 hour Locksmith Service or purchase a replacement remote.
But, you may be able to save money by fixing an old key fob instead of replacing it. This is particularly true if the problem is due to an old switch or a damaged contact.
Battery
If the buttons on your key fob aren't responding when you pressing them, this could be a sign the battery is dead or is close to the end of life. It's simple to replace the battery on your own instead of hiring locksmiths or dealers.
First find the battery compartment. This is usually found on the backside of the key fob. It could be hidden behind the cover, which slides out, or an access point that opens when you push the button. After the compartment is opened then look for the small button-cell battery. This is typically shaped like a coin and identified with an minus and plus sign. Take the old battery out, and replace it with a new one. Make sure that the plus and the minus symbols are properly aligned.
Once the battery is in place, close the compartment and snap the two parts of the key fob together. Be sure to align the two pieces and secure them correctly prior to closing the door and testing your keys. To test whether the buttons function properly, press any of them.
If your remote keyfob doesn't work after replacing the battery, there may be other issues that require a different type of repair. Dropping the fob into a pool of water can cause it to stop functioning. Alternatively, it might be experiencing an electrical issue within the device or may need to be deprogrammed by an expert or locksmith. Check out these other common automotive troubleshooting methods to determine whether your key fob is suffering from a different issue.
Switches
There are a variety of switches found in the car key fob, depending on the year and model. The older style key has an embedded chip that can be seen in the case. The latest keys operate by sending signals to your car. The keys' buttons can be worn out or damaged through normal use, regardless of the type. This causes them to become difficult to press, or even ineffective. If you try to press the button too hard, it can cause further damage and potentially stop the key from being able to start your vehicle in the future.
If your key doesn't appear to be working, you should first try changing the battery. If TheKeyLab doesn't work, then you might have to clean your key fob or adjust its switches. These tiny electronic switches are more susceptible than larger components of the key to break due to the fact that they are constantly jostled.
The switches feel rubbery and are coated with a film that conducts electricity. This film can fade over time. However, they're a small part that is easy to replace. They are soldered onto the circuit board, therefore it is important to take them off without causing any damage to anything else. Then, you can solder in the new ones and rebuild your key fob.
Avoid using your car key fob for more than a couple of hours at a stretch and avoid leaving it visible. If you don't use your key, store it in a safe place.
If you've already tried cleaning your key fob and replacing the battery, but the problem persists it's probably time to consider the services of a locksmith. A professional locksmith will test your key's frequency to see whether your car is capable of communicating. They can also open and replace microswitches, change cases, and much more.
Outer Case
A key fob spends much of its time bouncing around and if the buttons aren't free to move between the case, they may become stuck or even broken. If replacing the battery or cleaning it with a cotton swab and some rubbing alcohol don't resolve the issue, taking off the case and examining it may be necessary. If the contacts that the buttons touch don't fit well or are worn out, adjusting them might be the only solution to fix the issue.
Rubber buttons may get worn out over time. Rubber buttons can become difficult to press because they stretch, and nails can cut them. This could cause the key to fail and in this instance it is time for the replacement of the case or buttons. This repair involves removing the remote, finding the buttons on the circuit board, and then heating the solder and carefully remove them. The circuit board is then soldered with new buttons. The case is then rebuilt with the horse shoe key blade piece is attached. The new buttons should be a close fit into the case in order to prevent them from falling out.
Inner Case
Since your key fob is likely get jostled around and may sometimes be accidentally pressed and the buttons inside may become stuck or broken over time. If your key fob stops working when you're away from home It is possible to fix the problem quickly by using metallic tape and punch holes. This will allow you to open doors but not start the vehicle. This quick fix may allow you to safely return to your vehicle to complete your trip.