15 Facts Your Boss Wished You Knew About Repairs To Upvc Windows

Repairs to uPVC Windows
uPVC windows are an excellent option for modern homes. They are durable, long-lasting and easy to maintain. As opposed to aluminium and timber they don't corrosion or rot.
It is essential to clean and oil UPVC doors and windows on a regular basis. This will prevent unnecessary repair costs as well as improve the efficiency of energy.
1. Broken Glass
The damaged glass in your windows can cause significant damage to your home and even be fatal. It is crucial to take the time to make sure that you're doing all you can to keep your windows in good condition.
Single-pane windows are relatively simple to replace, and they generally fit into frames that were previously in use very easily. If windows with double panes are held together by internal beading, it will be more difficult to remove and replace the panes that were previously in use. In this instance it is essential to buy plastic spacers to aid in fitting the new pane into the window frame.
Wearing eye protection and heavy gloves is a must for anyone who plans to remove the glass by yourself. It is also recommended to lay down a drop cloth prior to when you begin working on the glass, so that any shards will fall on the fabric instead of onto the floor where they could be trampled upon and cause further damage.
Once the glass has been removed and the glass is removed, it's a good idea to seal the gap with packaging tape or duct tape to prevent water and drafts from entering the home until a professional is able to come out and repair the window. It also acts as a barrier, preventing any intruders to gain access to your home. If the gap is large, you might think about a security door that has an integrated window, as it will provide the best of both worlds.
2. Sagging
uPVC is a durable, energy-efficient and affordable alternative to timber sash windows. However, over time, they can suffer from a variety of issues like sliding. A sagging window in uPVC can cause issues with light, draughts and even security. It's crucial to act immediately if you discover that your uPVC windows are sagging.
Repositioning the hinges can help fix a window that is sliding. To do this, you'll have to open the window so that you can get to the frame. With the screwdriver, you'll be able to take off the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. Close your window to test the fit after you have relocated your hinges. If you're satisfied with the fit of the window, tighten the screws to hold them in place.
If you are unable to move the hinges, you may need to replace the seal. Over time rubber seals can lose their elasticity and become dry, which causes them to loosen. If this happens, it's important to replace the seal as soon as possible to ensure your uPVC windows are watertight and safe from drafts.
uPVC handles can also become loose. This is often caused by screws that have loosened over time, but it can also be caused by the handle mechanism wearing out. It's a good thing that it's simple to fix the handle of a window that is loose yourself. First, you'll need to shut the window and perform an experiment fitting. The corner joints of the sash must align with the casing joint. If it isn't then you can use the screwdriver to loosen the handle. Then, turn try what she says to position.
3. Water Leaks
It is crucial to take action if you get up each morning to find mouldy walls and floors that are wet. Windows that leak water do can not only cause degrading of the structure of your home but also hamper your efforts to regulate the temperature within your home. Most often, uPVC window leaks are caused by damaged or missing sealant.
This is a relatively easy fix that can be completed by any DIY expert. Depending on the severity of the issue is, the old caulking may need to be removed. It is important to remember that when it comes to uPVC window repairs, you should not be tempted to 'over-caulk' as this will only make the area harder to clean and could reduce your energy efficiency.
It is crucial to make sure that the drainage holes are free of debris and that the sill pan has been angled properly so that it drains away from the window. In more serious cases you might have to consider replacing the window.
Other indicators of water leakage are sills that are rotten and the appearance of black spots of mold on the wall near the window. This fungus thrives in damp conditions and is able to quickly spread throughout the house.
If the leakage is occurring between the double-glazed glass it is more likely the issue is more with the seal than the frame. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.
4. Faulty Hinges
Hinges could be at fault if your uPVC window is difficult to open or it blows open with a breeze. They can be replaced by any competent DIYer and can be done within a few minutes.
Like any mechanical component hinges are prone to wear out over time. It is essentially a simple process but it can be simpler if you have someone to assist in holding the frame in place.
It is also worth checking that the uPVC hinges are opening and closed in the right direction. You can do this by looking for the arrow on each hinge. This indicates the direction in which the window should be opened.
Window hinges that aren't working properly could be caused by improperly opening the window a certain manner or because of improper installation in the factory. Sending us photos via our website will often solve the issue. We are more than happy to provide suggestions.
Regularly lubricating the hinges is essential. Applying a light engineering lubricant to the hinges is an ideal method to accomplish this. We recommend using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can allow the window operate and close more easily. It also helps prevent corrosion and decrease the chance of sticking. This should be done at least every year. WD40 or other solvent-based lubricants should not be used as they can damage your uPVC windows.
5. Draughts
Draughts in upvc windows can be caused by various factors. The hinges may also become misaligned due to wear, which can cause gaps where the sash meets frame. If they're beyond repair, it might be required to realign them. Secondly the interlock, this is located on the hinge side of the window, may be misaligned. Again, it is possible to give them a thorough clean, however in some cases it might be necessary to have them replaced.
These seals are susceptible to wear and tear or become damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity glasses. This will help regulate indoor temperatures and decrease the possibility of draughts.
One of the most effective ways to reduce the draughts in your home is to use an draught excluder. These are typically fabric tubes that are filled with some type of filler. They can be positioned on top of your windowsill. They will help stop cold air from entering and keep your home warm and cozy!
Your upvc windows can remain a great source of insulation and security to your home with regular maintenance and repairs. It is crucial to keep in mind that all windows eventually become worn out, and it could be cheaper to replace them instead of fixing them. If you have any problems with your upvc window you should consult a professional immediately.