Repair Car Keys Its Not As Difficult As You Think

How to Repair Car Keys
The car keys are small and may not seem important, but they're vital to the functioning of your vehicle. Replacing a traditional or a modern transponder key can cost up to $200.
However, there are ways to fix your car keys at home with only a fraction of the cost. This article will cover the most frequent car keys issues and their DIY solutions.
Dead Key Fob Battery
The remote key fobs for keys that come with cars make it easier than ever to open the trunk, doors and the tailgate. The battery inside this device is susceptible to dying. There are a few tricks you can use to solve this issue quickly.
Check to see if the vehicle is still in ignition mode. If it is the battery of the key fob might be low instead of dead. To test this, push the button on the key fob right up against the vehicle's ignition button. If this works, then the battery is probably fine and only requires to be replaced.
To replace the fob's battery, begin by prying the case off using the help of a screwdriver or watch-type device. Don't apply too much force, as this may cause the fob's case split. If the fob doesn't seem to be coming easily, try putting your pry tool in more than one place on the outside of the case.
Open the electronic portion of your vehicle after you have removed the mechanical key. Insert the new battery and then snap back the shell. If your key fob doesn't work after this, it could be that there is an problem with the remote start system of your car. This requires a professional to diagnose. If this is the case, a trusted mechanic should be able help you. You can also call roadside assistance to assist with your vehicle if needed.
Broken Key Ring
There are a few options you can do if your key fob doesn't work because the ring has been broken. The first step is to see if the damaged piece is still in the ignition. If it's still inside the ignition, take it out without damaging the ignition lock or the door lock. Call a locksmith if you are having trouble taking the key off. They have special tools to safely remove a broken key from the ignition.
Another common cause of a broken car key is the corrosion of the circuit board or frame. Clean the board with cotton swab. This will eliminate the corrosion and protect to the contact pads.
You can repair a damaged ring by using a thick wire or nail to close the hole. Superglue can also be used to fix a broken ring. First, clean the damaged rings with a damp cloth and then apply a small amount superglue to the ends of the nail or wire. Allow the pieces to dry, and then press them together. These DIY solutions might seem appealing, however they are only temporary solutions. For long-term repairs, you'll want to get an experienced locksmith. They have the tools and knowledge to repair a damaged car key quickly and effectively. They can replace the battery and reprogram your key fob, if needed.
Broken Key Blade
Key blades may break from a lot of wear and tear. If this happens, it's time to purchase a new key. Luckily, this problem isn't as serious as it might seem at first glance. The problem is that the metal blade has snapped away from the case.
Spraying lubricant into the keyhole is a solution to repair it. Then, you can use pliers pins, or tweezers to grab the damaged key and pull it out. You can also employ a magnet in the event that the key is magnetic. Use a magnet to assist you remove the key, but take care to not break the lock tumbler.
Contact a locksmith right away in the event that you are unable to remove the broken part of the key. They have tools that let them safely remove keys without causing damage.
You can also try super glue to repair a snapped key. Apply a small amount glue to the edges of the crack and press them together. Wait until the glue dries before inserting your key into the lock. But this method isn't very reliable and you might have to repeat the process multiple times before it's successful. Super glue may not be able to hold the key in place. Therefore, this is more of a temporary measure than an option that can last.
Broken Plastic Loop
If your key fob's plastic loop is damaged it can render the key useless. It's a fairly easy fix. You can make use of wire or a nail for finishing as a replacement. For each end of the wire or nail, drill two holes into the plastic loop. Cut the wire or nail to a key width, then put the superglue drop in each hole. Apply the nail or wire into the holes and let them dry.
Another option is to purchase a replacement shell from a locksmith that sells them. They can take the programmable component of your key, move it to the new shell and cut an entirely new blade for less than a full replacement cost.
This isn't the best option, but it can help you get back on the road once more if your key split in half. It's difficult to fix when the blade of the key is inside the ignition, however. You could try using a hair clip or a needle extractor tool to pull the broken part of the ignition, however this is risky if you're not careful. The best solution is to call a locksmith with special tools for safely removing damaged keys from the ignition. You can also have an entirely new key made using appropriate cuts for the ignition of your vehicle.
Broken Master Key
If a key is broken inside the lock, you'll have to try to retrieve it before it gets completely destroyed. You can use tweezers, lubricants, and needle nose pliers to grab the fragments of a damaged key.
To begin, spray the inside of your lock with a lubricant such as WD-40 or graphite powder. You can also try the hacksaw blade method that involves carefully sliding the blade along the edge of the broken key and connecting to a few of the 'teeth' - if you succeed in doing this you should be able to remove the broken key from the lock.
Another useful tool is an extractor for keys spiral, which you can find in a wide range of hardware stores. It's a thin and flexible bar with spiral threads, which can be put into the keyway and bent to reach into the broken part of the key. Once car key remote repair near me has gotten caught on the serrations, you can twist the bar around and then pull it against the damaged section of the key.
Before contacting a locksmith try to remove the broken master key. If you are unable to get an item out, it's time to call in the big guns and have a locksmith make you a brand new key and reprogram it to the transponder of your car.